Remove furniture or place it in the center of the room and cover with drop cloths. Place drop cloths or tarps on the floor and remove window coverings, switch plates and outlet covers. Use painter's tape to protect windowsills, baseboards, door hinges and the ceiling perimeter.
Paint a Room
If this is your first time painting a room you're in luck. It's a great project for any novice do-it-yourselfer. With the right tools and advice, you can give any room in your home an instant update without spending a lot of time or money.
Step 1: Prepare the Room
Step 2: Clean & Repair Walls
Properly cleaning and repairing surfaces is extremely important when painting since paint doesn't adhere to dirt. Using a sponge or cloth, wipe down your walls with mild detergent and water and allow to dry. If your walls have cracks, holes or other damage, apply spackling compound or acrylic caulk with a putty knife. Sand with fine sandpaper once it dries.
If you need to make repairs, add an extra day to your plans to give the compound time to dry.
Step 3: Prime
When interior painting, you don't have to apply a coat of primer before you paint, but doing so will make the paint adhere and wear better. Additionally, priming is advisable if your walls are stained or you wish to use light-colored paint over dark walls. Apply True Value EasyCare® Ultra Premium latex primer/sealer with a brush or roller, using the same technique as painting. Note: You can also skip this step by painting with True Value EasyCare® Ultra Premium latex paint and primer in-one.
Open the windows to make sure you'll be priming and painting in a well-ventilated area.
Step 4: Paint the First Coat
Okay, let's roll — ceiling first, then walls. When painting a ceiling you can either use an extension pole that is attached to a roller, or set up scaffolding. Pour EasyCare® Ultra Premium latex paint and primer in-one into the paint tray and coat your roller. Paint widthwise in 6-ft. square sections, using a zigzag pattern of overlapping "W" strokes. Move from right to left, then left to right, spreading evenly with horizontal strokes.
"Feather" (apply less pressure to) the edges of the squares to eliminate overlapping lines between each section. To ensure even coverage, use light strokes to re-roll across the ceiling and from bottom to top of each wall. If your paint has a flat finish, you don't need to blend. Otherwise, paint over the entire surface (for very large areas, do two square sections at a time) with one-directional, overlapping, non-diagonal strokes once again.
Use our paint calculator to estimate how much paint you need before you begin the project.
To prevent the paint from drying unevenly, avoid stopping while you're in the middle of painting a wall. Touch up any missed spots when the paint is still wet to ensure an even sheen.
Before you begin painting a new wall, make sure you have enough paint left in the can to finish the entire wall. The same paint color can vary slightly from one can to another, so try not to use two different paint cans on one wall.
Step 5: Apply Wall Brushwork
Use a brush, coated with one inch of paint, to do wall brushwork in areas your roller can't reach, like the corners and next to the doors, windows and molding.
Step 6: Paint The Second Coat
If necessary apply a second coat of paint using the same technique as the first. You don't have to let the paint completely dry between coats, but your results will be better the longer you wait.
Step 7: Clean Up
You're almost done! Thoroughly rinse your roller covers and brushes in water until the solvent runs clear. Store in plastic bags or hang them on nails or hooks to dry. Remove the drop cloths and pull off the painter's tape at a 45-degree angle to avoid removing any fresh paint.
So you don't waste paint, combine any leftovers in a mixing bucket and store properly.
Great job! Step back and admire your updated room. We hope that finishing this home improvement project successfully will give you the confidence to keep painting!
Here’s what you’ll need to complete this project successfully.
Before you begin, use the shopping list below to uncheck the tools you already have to complete this project.
Then, print or save your updated list and bring it to your local True Value hardware store, where an expert Hardwarian will give you the remaining tools and expert advice you need to complete this project.
You can also shop online for these project items at TrueValue.com and receive FREE shipping to a participating store.
Top Spring Projects
Sign up now to receive special offers and project ideas via email.