Maintain Gutters and Downspouts
Bernie Duggan - Bradford, PA

Hardwarian Bernie Duggan

Horns True Value Hardware

Bradford, PA

Maintain Gutters and Downspouts

Level: Beginner

Gutters and downspouts keep water away from your home's foundation and are essential to any home's structural health. By taking care of your roof's drainage system, you can extend the life of your roof and help prevent water damage to your home. Follow the steps below to learn how to effectively clean, repair and maintain your gutters and downspouts.

Share this project
Print
Project Steps
Project Shopping List
  • Clean Gutters and Downspouts

    A clean gutter is a properly functioning gutter. Here's how to keep them clog-free and running smoothly

    • Step 1: Inspect gutters
       
      clean gutters and downspouts

      Before you can clean your gutters, you have to see what kind of shape they're in. See if your drainage system shows any signs of corrosion, look for any holes or leaking joints and check for any loose, missing or bent gutter hangers. Use masking tape to mark where there are problems so you can go back to them quickly when you are ready to make repairs.

    • Step 2: Clean Them Out
       

      For water to flow through your gutters unfettered, you need to remove the debris that can collect in gutters. Handheld blowers or wet/dry vacuums are effective tools for removing debris, particularly on dry days when leaves are loose and light. Blow out as much loose debris as possible and collect it in yard refuse bags.

      Use a gutter scoop to remove compacted debris. Attach a bucket to your ladder with a wire hook for more efficient collection or to carry tools. Start at the downspouts and work your way in, but avoid pushing debris together—this can create more clogs.

      Safety Alerts!

      Wear heavy gloves for protection. Sharp objects such as thorns and roofing nails can end up in gutters.

      Take the necessary precautions when working on a ladder. When using a ladder to reach high areas, you may want to invest in an adjustable ladder stabilizer.

    • Step 3: De-clog the Downspout
       

      If you have a clog but can't tell where, check the downspout. Clogs can happen where the downspout connects to the gutter. Remove the elbow joint and inspect all parts for clogs. If the blockage is out of reach, de-clog from the bottom up to avoid packing the clog tighter. Run a garden hose through the downspout with a rag tied around it to prevent water from splashing back. Turn on the water full blast until the clog breaks apart and water starts coming out of the downspout. If the clog is stubborn, try using a plumber's snake in a similar manner. If that doesn't work, pull down the downspout and use a broom handle to clear the blockage.

    Repair and Maintain Metal Gutters and Downspouts

    Sometimes it's more than a clump of muck and leaves preventing your gutters from working properly. You may need to make some minor repairs.

    • Step 1: Repair Small Holes
       

      Repair any small holes or cracks in your gutters and downspouts with a gutter patching kit.

    • Step 2: Patch Leaks and Tears
       

      Remove any rust or peeling paint with a stainless steel wire brush. Cover the scraped-off area with a rust treatment solution or rust-inhibiting paint and allow it to dry. Then apply a 1/8" thick layer of gutter repair cement or roof cement. To prevent a dam from forming, you'll need to flatten and smooth the edges of the cement. While the cement is still wet, cover the area with strips of heavy aluminum foil. Press the patch down tightly with a dry cloth to finish.

      Helpful Tip

      When joining two pieces of patch material, overlap them in the direction of water flow. Cement the edges together securely to prevent liquid from entering at the seam. This will also maximize drainage speed.

    • Step 3: Replace Damaged Gutter Sections
       

      If you need to replace a gutter section, remove any gutter hangers that are in or around the damaged area using a screwdriver or pry bar, depending on what type of gutters you have. Put a 4"x4" block of wood inside the width of the gutter to prevent the gutter from becoming misshaped when you add pressure. Remove the faulty gutter section with a hacksaw, then cut a new section of gutter that is 2" longer than the damaged area on each side to allow for overlap.

      Using a stainless steel wire brush, scrub the inside edges of the existing gutter. Caulk the area about 2" in on the sides and bottom with gutter caulk. Center the new piece into the old gutter so the caulk is covered on both ends and press it in. Screw or rivet the pieces together, caulking over exposed screws. Reattach the gutter hangers when you're finished.

    • Step 4: Adjust Pitch of Gutters
       
      True Value 5 gallon bucket

      When your gutters were first installed, they had a drop of approximately 1/16" for each foot of gutter. Make sure the drops are still there; if not, you'll need to readjust the pitch of your gutters. Use chalk and a level to take a reading and record the slope of your gutters.

      Another way to check the pitch is to pour a bucket of water into the gutter and observe the flow. If it runs off without leaving pools of water in the gutter, the gutter is set properly. Any high or low spots can often be corrected by slightly bending the hanger that supports the gutter. You may need to add additional gutter hangers to raise or lower the slope of the gutter at any given point.

    • Step 5: Install Gutter Screens or Guards
       
      aluminum downspout

      Once your gutters are cleaned and repaired, you'll want to keep them that way. To prevent gutters from filling with leaves and other debris, install a metal gutter screen or, ideally, an aluminum gutter guard. Watch out for inexpensive screens. They might keep leaves out of your gutter, but these inexpensive screens can trap leaves near the screen and cause other roof problems. Gutter guards extend across the entire width of the gutter, allowing water to enter while leaves and foreign materials go over the side.

      Nice work. Now you can rest assured that your gutters will work during even the worst storms without clogging and protect your home the way they should.

  • Here’s what you’ll need to complete this project successfully.

    Before you begin, use the shopping list below to uncheck the tools you already have to complete this project.

    Then, print or save your updated list and bring it to your local True Value hardware store, where an expert Hardwarian will give you the remaining tools and expert advice you need to complete this project.

    You can also shop online for these project items at TrueValue.com and receive FREE shipping to a participating store.

    Clean Gutters and Downspouts

    Repair and Maintain Metal Gutters and Downspouts

    60 character limit.
  • Alternative Mulch Landscaping Ideas

    There are a number of mulch alternatives to consider.

    Learn More

  • Top Spring Projects

     
  • How to Make Compost

    Learn how to make compost for your lawn and garden.

    Watch Video

  • Follow Us On Pinterest

    Follow Us On Pinterest

    Visit our Pinterest page for great do-it-yourself project advice and home inspiration.

    Follow Us

  • Behind Every Project Is a True Value

    Behind Every Project Is a True Value

    Get the projects and advice you need to get your projects done right.

    View Commercial