Build a Rain Water Collection System
Bill Johnson - Groton, CT

Hardwarian Bill Johnson

Johnson True Value Hardware

Groton, CT

Build a Rain Water Collection System

Level: Experienced

Homeowners use a lot of water every year watering the lawn or garden, which means that a lot of water and money goes, as they say, down the drain. Installing a rainwater collection system at the end of your gutter downspouts controls excess surface water and buckets it for use on your lawn. Cut down on needless water use and save money by trying this natural resource-saving irrigation technique.

Share this project
Print
Project Steps
Project Shopping List
    • Step 1: Get a Container
       
      barrel collecting waterbarrel

      You need a fairly large container to collect the water when it comes down the spout from your gutters. A 55-gallon barrel or cistern is all you need to hold enough water for watering your lawn and garden or to wash your car. You can buy specially designed containers for collection; these containers come with outlets for hoses and for filling watering cans. To save money though, you can make your own container out of a polyethylene, fiberglass or metal barrel or drum, which is what this project will focus on.

      Safety Alerts!

      Only use containers meant to hold water or food. Don't use any container that once held chemicals.

      Never use the water collected for drinking.

      Helpful Tip

      Check with your local municipal officials to make sure it is legal to collect and hold water for reuse.

      Place your rainwater container on concrete cinder blocks near where your gutter downspout ends. Stack the concrete blocks so that the container is level, sturdy and won't tip over. You'll most likely need about four blocks so that you can stack them and raise the container about 2' off the ground, which will make it easier to retrieve water.

    • Step 2: Make a Filter Top
       

      Make the top of your rainwater container by cutting off the top of a 5-gallon bucket. The bucket's lid will be used to secure a paint strainer to the top of the bucket, thereby keeping large objects, mosquitoes and other insects and debris from getting into the barrel and spoiling your water supply.

      Use a power drill with 7/8" spade bit to punch a hole in the side of the 5-gallon bucket. This will make it easy to cut off the top with your jigsaw. Then secure a mesh paint strainer to the bucket opening to filter out objects and mosquitoes in your barrel or drum. Discard the rest of the bucket scrap. Keep the bucket lid (you'll need it later).

      Helpful Tip

      To prevent matter from hanging too far down into the rain barrel, tie a knot in the strainer before installing it into the lid.

      Next, use a permanent marker to trace a circle around the newly cut five-gallon bucket top onto the top or lid of your large 55-gallon water container.

      Use your drill (with the same 7/8" spade bit) to punch a hole in the top of the 55-gallon container and then use the jigsaw again to cut along the traced circle. After being cut, the top of the 5-gallon bucket should fit perfectly in the opening of the large container.

      Next, use a permanent marker to trace around the bottom edge of a gutter extension on the top of the bucket lid. Use the 7/8" bit to drill a starter hole and then cut the lid with your jigsaw to fit the gutter extension. Place the lid on the top of your new filter to check for proper fit.

    • Step 3: Attach Gutter Extension
       
      attacher

      Using the existing downspout from your gutters, add an extension — your local True Value hardware store carries a variety of extensions and fittings for this type of alteration.

      Measure and mark where you need to cut the fitting so that the end will run into the top of your collection barrel. Most fittings are made of flexible plastic and can easily be cut with a utility knife. Note that it may be necessary to use a splice to fit the end of your existing downspout into the extension. Push the two pieces together until they are snug and seal them together with an appropriate adhesive. Use brackets to secure the fitting to the side of your house.

    • Step 4: Install a Spigot
       

      Lastly, you need a way to get the water out of your collection system. Put in a spigot at the bottom of the container by drilling a hole using the 7/8" spade bit. File down the rough inside edges of the hole with a metal file and then screw in a 3/4" spigot securely. Seal around the spigot with waterproof silicone caulk. Be sure that the spigot is facing the right way on the barrel so you can access it easily when you start actually using it. Simply turn the spigot handle and fill up buckets or watering cans.

    • Step 5: Install Water Pump (Optional)
       

      If you plan on connecting a garden hose to the spigot to water your garden or wash a car, you may need to install an irrigation pump or water-pressure booster pump. Without a pump, you might not have enough water pressure to push the water from the container through the hose with enough force. To get close to the same amount of water pressure as a standard household tap, a pressure-boosting pump is essential.

      Take into account the size of your yard or garden when choosing a pump. A small pump is good for a standard, tiny garden, while a larger pump with more horsepower is needed if you're going to water a normal-sized yard. An expert at your local True Value hardware store can help you pick the pump that is right for you. Because pump models differ widely by manufacturer, the method of connecting one to a rainwater collection system can depend on the specific pump. After you've purchased the pump you need, follow the supplied instructions carefully during installation.

      Great job! You're done. Now let your gutters and the rain do the work. You'll soon have a reservoir of free water to care for your lawn and garden.

  • Here’s what you’ll need to complete this project successfully.

    Before you begin, use the shopping list below to uncheck the tools you already have to complete this project.

    Then, print or save your updated list and bring it to your local True Value hardware store, where an expert Hardwarian will give you the remaining tools and expert advice you need to complete this project.

    You can also shop online for these project items at TrueValue.com and receive FREE shipping to a participating store.

    60 character limit.
  • Alternative Mulch Landscaping Ideas

    There are a number of mulch alternatives to consider.

    Learn More

  • Top Spring Projects

     
  • How to Make Compost

    Learn how to make compost for your lawn and garden.

    Watch Video

  • Follow Us On Pinterest

    Follow Us On Pinterest

    Visit our Pinterest page for great do-it-yourself project advice and home inspiration.

    Follow Us

  • Behind Every Project Is a True Value

    Behind Every Project Is a True Value

    Get the projects and advice you need to get your projects done right.

    View Commercial